Free 2021 JNCIP-SP JN0-663 dumps are available on Google Drive shared by PracticeVCE
Welcome to download the newest PracticeVCE JN0-663 PDF dumps: https://www.practicevce.com/Juniper/JN0-663-practice-exam-dumps.html ( 95 Q&As)
NEW QUESTION 36 
You are the administrator of AS 65512. You are learning the 192.168.1.0/24 prefix from both AS 100 and AS 200. You want traffic destined to the 192.168.1.0.0/24 prefix to exit your AS towards AS 200.
How would you accomplish this task?
- A. Configure an import routing policy on PE-2 to modify the origin attribute on the path learned from AS
100. - B. Configure an import routing policy on PE-2 to append the AS path attribute on the path learned from AS
100. - C. Configure an import routing policy on PE-2 to set a higher local preference value on the path learned from AS 200.
- D. Configure an import routing policy on PE-2 to set a higher MED on the path learned from AS 100.
Answer: C
NEW QUESTION 37
Exhibit:
You are receiving the same 200.0.0.0/24 BGP route from four different ISPs.
Referring to the exhibit, which ISP's route would be selected as active?
- A. ISP-A
- B. ISP-D
- C. ISP-B
- D. ISP-C
Answer: B
NEW QUESTION 38
Exhibit:
You have an established Layer 3 VPN between two PE devices. You are asked to only send certain routes from PE-1 over the VPN to the remote site while maintaining all the routes on the PE-1 device. You created a policy that matches the specific routes and then tags these routes with the appropriate target community values.
In this scenario, which configuration changes must be made to satisfy the requirement?
- A. Configure the import parameter and apply the policy to the my-ext-group BGP group configuration.
- B. Configure a RIB group and apply the policy as an import policy to routes distributed into the bgp I3vpn.0 routing table
- C. Configure the export parameter and apply the policy to the my-ext-group BGP group configuration.
- D. Configure the vrf-export parameter and apply the policy under the edit routing-instances vpn-a hierarchy.
Answer: D
NEW QUESTION 39
Exhibit:
Referring to the exhibit, what will the IS-IS cost be for R1 to reach R3?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 40
Exhibit.
You are providing camer-of-carner VPN services for AS 100 and AS 200 You want to distribute MPLS labels between your PE routers and the AS 100 and AS 200 CE routers.
What must be enabled to accomplish this task?
- A. Use RSVP with the tunnel-services parameter enabled
- B. Use BGP with the labeled-unicast address family enabled
- C. Use BGP with the inet-vpn address family enabled
- D. Use RSVP with the lsp-set parameter enabled
Answer: C
NEW QUESTION 41
Exhibit:
R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which two configuration changes will allow load balancing? (Choose two.)
- A. Apply the prepend policy as an import policy under group R3.
- B. Configure muitipath under the global BGP configuration.
- C. Apply the prepend policy as an import policy under group R1.
- D. Configure muitipath under group R1.
Answer: B,C
NEW QUESTION 42 
You are troubleshooting a problem with a BGP peer where BGP routes are not being accepted from that peer.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. The reject at the end of the policy is preventing the routes from being accepted.
- B. Term 0 is missing a terminating action that allows BGP routes to be accepted.
- C. Term 0 is missing a route-filter that specifies the allowed routes.
- D. You cannot have terminating actions outside of terms.
Answer: A,B
NEW QUESTION 43
Exhibit:
All adjacencies have been formed, no extra options have been configured, and no policies have been written.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. R1 can reach R5.
- B. R2 will create a default route and send it as a TLV to R1
- C. R1 cannot reach R5
- D. R1 will create its own default route that points to R2
Answer: A,B
NEW QUESTION 44 
A network designer wants to ensure that traffic from R2 destined for 2001:db9:ffff:ff00::/62 always traverses the R2-R1 link if that link is available.
Referring to the exhibit, which configuration change will satisfy this requirement?
- A.
- B.
- C.
Answer: A
NEW QUESTION 45
Exhibit:
Referring to the exhibit, which two statements about route reflectors are correct? (Choose two.)
- A. RR2 advertises routes learned from Client3 to EBGP2 with itself as the next hop.
- B. RR2 adds its cluster ID when advertising routes from CHent4 to Client3.
- C. RR1 and RR2 need the same cluster ID to exchange routes learned from their clients.
- D. RR1 advertises routes learned from Client1 to RR2 with itself as the next hop.
Answer: A,B
NEW QUESTION 46
You are deploying a new EVPN service for your customers. You must build the service based on the following requirements
-- both Layer 2 and Layer 3 functionality must be supported
-- your customers must be able to support multiple VLANs in the same EVPN instance (EVI).
In this scenario which two types of routing instances should be configured? (Choose two.)
- A. virtual router
- B. VRF
- C. EVPN
- D. virtual switch
Answer: B,C
NEW QUESTION 47 
A network administrator is investigating why traffic from R2 is not being forwarded to R1.
Referring to the show isis databasecommand output shown in the exhibit, what is causing this problem on the network?
- A. R2 is ignoring specific LSPs from R1 in its SPF calculations.
- B. The preferred interface between R1 and R2 is experiencing errors.
- C. R1 and R2 are in different IS-IS areas.
- D. R1 is configured to drop all incoming traffic.
Answer: A
NEW QUESTION 48
You are creating an LDP-signaled Layer 2 circuit between two sites. Site1 and Site2 use different VLAN IDs to connect to your PE devices In this scenario, which encapsulation type must be used on the logical interfaces?
- A. vlan-tcc
- B. vlan-bridge
- C. vlan-ccc
- D. vlan-vpls
Answer: A
NEW QUESTION 49
Click the Exhibit button.
A network administrator is investigating why traffic from R2 is not being forwarded to R1 Referring to the show isis database command output shown in the exhibit, what is causing this problem on the network?
- A. R2 is ignoring specific LSPs from R1 in its SPF calculations.
- B. R1 and R2 are in different IS-IS areas.
- C. The preferred interface between R1 and R2 is experiencing errors
- D. R1 is configured to drop all incoming traffic.
Answer: A
NEW QUESTION 50 
Referring to the exhibit, traffic sent from CE-A2 to PE3 does not loop back to CE-A2 through PE2.
Winch two EVPN functions accomplish this task? (Choose two.)
- A. designated forwarder election
- B. multicast ingress replication
- C. aliasing
- D. split horizon
Answer: A,D
NEW QUESTION 51
Exhibit.
You have a Layer 3 VPN established between PE-1 and PE-2 to allow communication between CE-1 and CE-2 You want to establish communication between CE-1 and CE-2.
Referring to the exhibit, which statement is correct?
- A. You will need a BGP export policy on PE-1 to redistribute the OSPF routes learned from PE-2 to the CE1 BGP neighbor
- B. You will need a VRF export policy on PE-2 to redistribute the OSPF routes learned from CE-2. through the Layer 3 VPN
- C. You will need a VRF import policy on PE-2 to advertise the OSPF routes learned from CE-2 through the Layer 3 VPN
- D. You will need a VRF import policy on PE-1 to receive the OSPF routes learned from PE-2. through the Layer 3 VPN
Answer: B
NEW QUESTION 52
You are asked to configure a series of interface policers and firewall filters, which include policers, on the same device You must ensure that the two configuration methods do not conflict.
What are two considerations when performing this task? (Choose two.)
- A. On inbound traffic, firewall filters are applied before interface policers.
- B. On inbound traffic, interface policers are applied before firewall filters.
- C. On outbound traffic, interface policers are applied before firewall filters.
- D. On outbound traffic, firewall filters are applied before interface policers.
Answer: B,D
NEW QUESTION 53 
You manage an MX Series device which includes the configuration shown in the exhibit. Traffic marked with DSCP 000011 is entering the ge-1/0/4 interface at 102 Mbps. The traffic exits the device on the ge-1/0/5 interface. No other traffic is transiting the router.
In this scenario, what happens to traffic exceeding 100 Mbps?
- A. Traffic exceeding 100 Mbps is redirected to a rate limiter.
- B. Traffic exceeding 100 Mbps is buffered.
- C. Traffic exceeding 100 Mbps is forwarded.
- D. Traffic exceeding 100 Mbps is dropped.
Answer: D
NEW QUESTION 54
Exhibit:
R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which two configuration changes will allow load balancing? (Choose two.)
- A. Apply the prepend policy as an import policy under group R3.
- B. Configure muitipath under the global BGP configuration.
- C. Apply the prepend policy as an import policy under group R1.
- D. Configure muitipath under group R1.
Answer: B,C
NEW QUESTION 55
Exhibit:
Your network is connected to two different ISPs and you notice that they are using your network for transit traffic.
In this scenario, which two configuration statements will solve this problem? (Choose two.)
- A. set policy-options as-path LOCAL-ROUTES " (65310 I 65441)+"
- B. set policy-options policy-statement ISP term REST then reject
- C. set policy-options policy-statement ISP term ROUTES then reject
- D. set policy-options as-path LOCAL-ROUTES "()"
Answer: B,D
NEW QUESTION 56
Exhibit.
Referring to the exhibit, there is an Layer 3 VPN setup that connects sites CE-A-1. CE-A-2 and CE-A-3 together Host-1 can communicate with Host-3. but Host-1 cannot communicate with Host-2 What must you do to solve the problem?
- A. Use BGP instead of static routing between the CE and PE devices
- B. Change the route distinguish^ in both routing instances to the same value
- C. Use the next-table configuration statement for static routes in the corresponding routing instances.
- D. Use the auto-export command in both routing instances
Answer: D
NEW QUESTION 57 
All networks shown in the exhibit contain more than one BGP speaker. You operate ISP A and must ensure that Customer Y sends their traffic to you over the directly connected link. Customer Y is not to be used for transit into your network.
What would you do to accomplish this task?
- A. Advertise routes to Customer X with the custom defined 0:0 community.
- B. Advertise routes to Customer Y with the custom defined 65535:65535 community.
- C. Advertise routes to Customer Y with the well-known no-export community.
- D. Advertise routes to Customer X with the well-known no-advertise community.
Answer: C
NEW QUESTION 58
Exhibit:
Referring to the exhibit, you want to reduce the CPU processing load on PE 2 by preventing the receipt of routes belonging to Customer B.
In this scenario, which Layer 3 VPN scaling mechanism provides this functionality?
- A. route refresh
- B. route target filtering
- C. route origin
- D. route reflection
Answer: B
NEW QUESTION 59
Which two statements about IS-IS are correct? (Choose two.)
- A. Level 1 intermediate systems exchange routing information with Level 1 intermediate systems in other IS-IS areas.
- B. A Level 1 router can only form adjacencies with other Level 1 routers.
- C. An IS-IS router sets the attached bit in the PDUs it sends to a Level 1 area to indicate that it is a backbone router.
- D. Level 2 routers can form adjacencies with either Level 1 or Level 2 routers.
Answer: B,D
NEW QUESTION 60
......
Tested Material Used To JN0-663: https://www.practicevce.com/Juniper/JN0-663-practice-exam-dumps.html
Following are some new JN0-663 Real Exam Questions!: https://drive.google.com/open?id=1YmJQxF58aQ0ftwM2__FT1-OI8TgxSX6i