Use JN0-363 Exam Dumps (2024 PDF Dumps) To Have Reliable JN0-363 Test Engine
JN0-363 PDF Recently Updated Questions Dumps to Improve Exam Score
NEW QUESTION # 121
Click the Exhibit button. Which statement is correct about the configuration shown in the exhibit?
- A. This policy will reject all prefixes because it does not end with a then accept statement.
- B. This router will take prefixes learned from external BGP and change the BGP next hop to itself before re-advertising them to IBGP peers.
- C. The NEXT_HOP_SELF policy must also be applied to the group called CUSTOMER_A for bidirectional communication to succeed.
- D. This router will take prefixes learned from internal BGP and change the BGP next hop to itself before re-advertising them to EBGP peers.
Answer: B
NEW QUESTION # 122
Click the Exhibit button. In the exhibit, all routers are sending routes to Router B
Which routes will be advertised from Router B to Router D?
- A. BGP routes learned from Routers A and C only
- B. BGP routes learned from Routers A, C and E only
- C. BGP routes learned from Router E only
- D. BGP routes learned from Router A only
Answer: B
NEW QUESTION # 123
You are deploying link aggregation groups.
By default, what are two considerations in this scenario? (Choose two.)
- A. Member links are required to be contiguous ports.
- B. All the ports must have the same speed.
- C. There should only be four member links per LAG.
- D. Member links can reside on different members within an MC-LAG.
Answer: B,D
NEW QUESTION # 124
Click the Exhibit button.
The routers shown in the exhibit are configured for segment routing.
In this scenario, what is the adjacency SID that Router B advertises to Router A?
- A. 0
- B. 10.1.1.1
- C. 1
- D. 10.1.1.2
Answer: D
Explanation:
Currently, Junos OS enables you to configure a SPRING node SID for IPv4 and IPv6 address families for each routing instance. This node SID is attached to an IPv4 and IPv6 router ID if the router ID is configured on the loopback interface. Otherwise, the lowest IP address assigned to the loopback interface is chosen as the node SID. Configuring a node SID through policy allows you to choose the loopback address that gets the node SID. If the node SID configuration exists and a policy is defined for node SID selection for the same prefix, then the policy configuration takes precedence.
NEW QUESTION # 125
Which two statements ate correct about the information shown in the exhibit? (Choose two.)
- A. This switch has a bridge priority of 8k.
- B. The root bridge's priority Is 4k.
- C. This switch is the root bridge for this spanning tree topology.
- D. The root bridge is reachable using the ge-0/0/14 interface.
Answer: B,C
NEW QUESTION # 126
Which new field is added to an IPv6 header as compared to IPv4?
- A. checksum
- B. version
- C. flow label
- D. fragment offset
Answer: C
Explanation:
https://www.omnisecu.com/tcpip/ipv6/comparison-between-ipv4-header-and-ipv6-header.php#:~:text=IPv6%20header%20is%20much%20simpler%20than%20IPv4%20header.&text=The%20size%20of%20IPv6%20header,are%20128%20bit%20binary%20numbers.&text=In%20IPv4%20header%2C%20the%20source,are%2032%20bit%20binary%20numbers.
NEW QUESTION # 127
Which three attributes are well-known mandatory BGP attributes? (Choose three.)
- A. origin
- B. next-hop
- C. local preference
- D. AS path
- E. MED
Answer: A,B,D
Explanation:
https://www.kwtrain.com/blog/bgp-pt2
NEW QUESTION # 128
Click the Exhibit button.
You have configured IPv6 over IPv4 tunneling, as shown in the exhibit. However, hosts connected to network 2001:0:0:1::0/64 cannot communicate with hosts on network 2001:0:0:2::0/64. The router R2 has a similar configuration as the R1 router.
How would you solve this problem?
- A. Configure the next hop of the inet6.0 static route to point to the IPv4 address of the remote router
- B. Configure the next hop of the inet6.0 static route to point to the physical interface between the routers
- C. Configure an IGP across the tunnel interfaces
- D. Configure an IPv6 address on the tunnel interfaces
Answer: A
NEW QUESTION # 129
Which three statements are true regarding the show system switchover operational mode command? (Choose three.)
- A. This command displays the status of the interface and process databases.
- B. This command displays the status of graceful switchover.
- C. This command can only be issued on the backup Routing Engine.
- D. This command displays the status of the kernel database.
- E. This command can only be issued on the master Routing Engine.
Answer: B,C,D
NEW QUESTION # 130
Click the Exhibit button. From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?
- A. The address is not in the aggregate range; the packet will be forwarded.
- B. The address is in the aggregate range; the packet will be silently dropped.
- C. The address is in the aggregate range; the packet will be dropped.
- D. The address is not in the aggregate range; the packet is sent to the Routing Engine.
Answer: C
NEW QUESTION # 131
To which multicast address is a VRRP advertisement packet sent?
- A. 224.0.0.18
- B. 224.0.0.13
- C. 224.0.0.6
- D. 224.0.0.22
Answer: A
Explanation:
https://tools.ietf.org/html/rfc3768
NEW QUESTION # 132
Click the Exhibit button. You configured an aggregated Ethernet bundle between R1 and R2. Unfortunately, the bundle is not working correctly.
Referring to the exhibit, which configuration change will solve this issue?
- A. The LACP mode should be changed to active on R1.
- B. The LACP periodic mode should be changed to fast on R2.
- C. The LACP minimum links configuration should be changed to 2 on R1.
- D. The LACP minimum links configuration should be changed to 1 on R2.
Answer: A
NEW QUESTION # 133
Referring to the exhibit, what will happen to untagged frames?
- A. The untagged frames are load balanced between VLAN 10 and VLAN 20.
- B. The untagged frames are dropped.
- C. The untagged frames are associated with VLAN 10.
- D. The untagged frames are associated with VLAN 20.
Answer: B
NEW QUESTION # 134
Click the Exhibit.
Referring to the configuration shown in the exhibit, which statement is true?
- A. Traffic destined to address 192.168.5.1 will take next-hop 172.16.1.3.
- B. Traffic destined to address 192.168.5.1 will alternate between next-hops 172.16.1.2 and 172.16.1.3
- C. Traffic destined to address 192.168.5.1 will take next-hop 172.16.1.2.
- D. Traffic destined to address 192.168.5.1 will take next-hop 10.0.1.1.
Answer: A
NEW QUESTION # 135
You are using RSVP to signal an MPLS LSP.
Which statement is true in this scenario?
- A. A secondary path must be configured to establish an LSP.
- B. The traffic engineering database must be used for all LSPs.
- C. A primary path must be configured to establish an LSP.
- D. LSPs can be configured without any traffic engineering constraints.
Answer: D
NEW QUESTION # 136
Exhibit
Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 137
......
Juniper JN0-363 certification exam is a specialist-level certification offered by Juniper Networks. Service Provider Routing and Switching, Specialist (JNCIS-SP) certification is designed for individuals who have a deep understanding of service provider routing and switching technologies. The JN0-363 exam is an advanced-level certification that requires a thorough understanding of Juniper Networks technologies and products.
JN0-363 Dumps Full Questions with Free PDF Questions to Pass: https://www.practicevce.com/Juniper/JN0-363-practice-exam-dumps.html
Free JNCIS-SP JN0-363 Official Cert Guide PDF Download: https://drive.google.com/open?id=1EiqtPbaVN7s9LAiJMTcMPtLd8EXzxfM7